ID-COOLING AS-120-ARGB-WR 120mm Case Fan vs ID-COOLING AT-120-W 120mm Case Fan: Spec Comparison
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
The id cooling as 120 argb wr 120mm case fan vs at 120 w 120mm case fan comparison helps you pick the right airflow solution. Both are 120mm fans from ID-COOLING. The AS-120-ARGB-WR focuses on reverse airflow and ARGB lighting for clean builds. The AT-120-W prioritizes high static pressure and durability for radiators. You need to decide if visual appeal or raw cooling power matters more.
Key differences
| Aspect | ID-COOLING AS-120-ARGB-WR Reverse Fan | ID-COOLING AT-120-W 120mm High Static Pressure Fan |
|---|---|---|
| Lighting | ARGB | not listed |
| Static Pressure | 1.67 mmH₂O | 5.04 mmH₂O |
| Bearing Type | not listed | Dual Ball Bearing |
| Blade Design | Reverse | Tip Ring |
| Max Speed | 2000 RPM | not listed |
Which one should you choose?
Choose ID-COOLING AS-120-ARGB-WR Reverse Fan if
- You want ARGB lighting visible on the intake side
- You need a reverse blade fan for consistent aesthetics
- You prioritize quiet operation at lower speeds
Choose ID-COOLING AT-120-W 120mm High Static Pressure Fan if
- You are mounting fans on liquid cooling radiators
- You need high static pressure to push air through dense filters
- You want a dual ball bearing for longer lifespan
Verdict: Choose the AS-120-ARGB-WR if you value RGB lighting and reverse airflow for case intake. Pick the AT-120-W if you need serious static pressure for radiators and dust filters. The AT-120-W also offers dual ball bearings for durability.
AS-120-ARGB-WR vs AT-120-W Specs
Static pressure power
The ID-COOLING AT-120-W delivers a substantial 5.04 mmH₂O of static pressure. This high rating makes it ideal for pushing air through dense radiators, tower heatsinks, or cases with heavy dust filters. In contrast, the ID-COOLING AS-120-ARGB-WR provides 1.67 mmH₂O of static pressure. While this is sufficient for standard airflow tasks, it is significantly lower than the AT-120-W. If you are mounting fans on a liquid cooling radiator or any high-resistance component, the AT-120-W offers much stronger performance. The AS-120-ARGB-WR is better suited for open airflow scenarios where high static pressure is not the primary requirement.
Noise level rating
Noise specifications are a key factor for quiet builds. The ID-COOLING AS-120-ARGB-WR lists a maximum noise level of 28.3 dB(A). This rating suggests it operates quietly during standard use. The ID-COOLING AT-120-W does not provide a specific decibel rating in its published specifications. Without this data, you cannot directly compare the acoustic output of both fans. You must rely on the AT-120-W’s feature of zero RPM fan stop for silent idle operation. For active noise comparison, the AS-120-ARGB-WR has the clear advantage due to its published low decibel figure.
Lighting options
Visual customization is a major difference between these two models. The ID-COOLING AS-120-ARGB-WR includes ARGB lighting. This allows you to sync colors with compatible motherboards for a customized aesthetic. The reverse blade design also ensures the lighting side faces outward consistently. The ID-COOLING AT-120-W does not mention any lighting features in its data. It is a functional fan focused on performance rather than visuals. If you want visible RGB effects in your build, the AS-120-ARGB-WR is the only choice. For a hidden or non-lit setup, the AT-120-W is a plain option.
Bearing type
The type of bearing affects longevity and stability. The ID-COOLING AT-120-W uses a dual ball bearing design. This type is known for extended lifespan, improved heat tolerance, and stable performance during high-speed operation. The ID-COOLING AS-120-ARGB-WR does not specify its bearing type in the provided data. Without this information, you cannot assess its long-term durability relative to the AT-120-W. The dual ball bearing in the AT-120-W is a verified feature for high-stress environments. This gives the AT-120-W an advantage in terms of known mechanical robustness.
Airflow direction design
Airflow direction impacts how fans fit in your case. The ID-COOLING AS-120-ARGB-WR features a reverse blade design. This provides reverse airflow while keeping the RGB side facing outward, which is useful for specific intake or exhaust placements. The ID-COOLING AT-120-W does not specify a reverse or standard airflow designation in its data. It is designed for high static pressure with a closed-loop motor to maintain RPM under resistance. If you need reverse airflow for aesthetic or specific cooling paths, the AS-120-ARGB-WR is the specialized choice. The AT-120-W is a standard high-pressure fan.
Which fan fits your build needs
Users wanting clean reverse airflow lighting
This fan uses a reverse blade design to keep the ARGB side facing outward. You get consistent lighting without frame struts blocking the view. It also reduces intake whistling from case grills. The 28.3 dB(A) noise level keeps gaming quiet while delivering 53 CFM airflow for standard setups.
Owners of dense radiators or filters
This model delivers 5.04 mmH₂O of static pressure, which is essential for pushing air through dense radiators and tower heatsinks. The closed-loop motor maintains stable RPM under resistance. Its tip ring blade design channels air vertically, reducing turbulence and ensuring efficient heat removal even when airflow resistance is high.
Seeking silent operation at low loads
The zero RPM fan stop feature allows this unit to spin down completely when temperatures are low. You get zero-noise operation during idle periods. It activates automatically only when cooling is needed. This dual ball bearing design also ensures long-lasting performance and heat tolerance during high-speed operation.
The products compared
ID-COOLING AS-120-ARGB-WR Reverse Fan
Best for: rear exhaust and outward-facing RGB
- Fan Size
- 120mm
- Max Fan Speed
- 2000 RPM
- Max Airflow
- 53 CFM
- Static Pressure
- 1.67 mmH₂O
- Noise Level
- 28.3 dB(A)
- Lighting Type
- ARGB
View on Amazon: ID-COOLING AS-120-ARGB-WR Reverse Fan Affiliate link
This 120mm fan uses a reverse blade design to direct airflow backward while keeping the ARGB lighting visible on the outside. It reaches 2000 RPM, moving 53 CFM of air with 1.67 mmH₂O of static pressure. Noise stays at 28.3 dB(A). It fits standard cases and coolers. You get variable speed control for quiet or high-performance setups.
Pros
- Reverse blade design for outward-facing ARGB
- Max speed of 2000 RPM
- 53 CFM airflow rating
- 1.67 mmH₂O static pressure
Cons
- Lower static pressure than high-pressure competitors
- Max noise level of 28.3 dB(A)
- No magnetic bearing mentioned
Good fit if
- You want visible RGB on the exterior side
- You need a rear fan for a single-tower cooler
- You prefer quiet operation under 30 dB
Skip if
- You need maximum static pressure for dense radiators
- You prefer standard forward airflow direction
- You want a fan with a magnetic bearing
Verdict: ID-COOLING 120mm Reverse ARGB Fan suits builders who prioritize outward-facing lighting and quiet operation over maximum static pressure. It is ideal for rear exhaust or single-tower cooler mounting.
ID-COOLING AT-120-W 120mm High Static Pressure Fan
Best for: radiators and high-resistance cooling setups
- Fan Size
- 120mm
- Static Pressure
- 5.04mmH₂O
- Bearing Type
- Dual Ball Bearing
- Compatible Device
- Radiator, CPU Cooler
View on Amazon: ID-COOLING AT-120-W 120mm High Static Pressure Fan Affiliate link
The ID-COOLING AT-120-W is a 120mm case fan built for high static pressure. It delivers 5.04mmH₂O of pressure, making it suitable for radiators and dense heatsinks. The dual ball bearing ensures longevity. A closed-loop motor maintains stable RPM under resistance. You will appreciate the zero RPM fan stop for silent idle operation.
Pros
- 5.04mmH₂O high static pressure rating
- Dual ball bearing for heat resistance
- Closed-loop motor for stable airflow
- Zero RPM fan stop for silent idle
Cons
- No addressable RGB lighting included
- Lacks PWM speed control mentioned in specs
Good fit if
- You need high static pressure for radiators
- You want durable dual ball bearings
- You prefer silent operation at low loads
Skip if
- You require RGB lighting effects
- You need high airflow over static pressure
Verdict: ID-COOLING AT-120-W High Static Pressure Fan is a practical choice for users prioritizing cooling performance and durability over aesthetics. It fits builders who need reliable pressure for radiators without noise during idle times.
Specifications side by side
| Spec | ID-COOLING AS-120-ARGB-WR Reverse Fan | ID-COOLING AT-120-W 120mm High Static Pressure Fan |
|---|---|---|
| Fan Size | 120mm | 120mm |
| Max Fan Speed | 2000 RPM | not stated |
| Max Airflow | 53 CFM | not stated |
| Static Pressure | 1.67 mmH₂O | 5.04mmH₂O |
| Noise Level | 28.3 dB(A) | not stated |
| Bearing Type | not stated | Dual Ball Bearing |
| Lighting Type | ARGB | not stated |
| Blade Direction | Reverse | not stated |
| Lighting | ARGB | not stated |
| Compatible Device | not stated | Radiator, CPU Cooler |
| Dimensions | 4.72 × 4.72 × 0.98 inches | not stated |
Frequently asked questions
Which ID-COOLING fan is better for rear exhaust?
The AS-120-ARGB-WR is the better choice for rear exhaust. It is designed with a reverse airflow configuration, meaning the blades push air away from the motor side. This orientation keeps the ARGB lighting visible from the outside of the case. You also get quieter operation during idle times, making it ideal for clean build aesthetics.
Does the AT-120-W support RGB lighting?
No, the AT-120-W does not support RGB lighting. The product data lists it strictly as a high static pressure fan without any lighting attributes. If you want visible illumination in your build, you should choose the AS-120-ARGB-WR instead. The AT-120-W focuses entirely on cooling performance and durability for radiators.
Can I use these fans for a CPU cooler?
Yes, both fans work with CPU coolers, but they serve different roles. The AS-120-ARGB-WR is suitable for single-tower coolers where you want outward-facing lighting. The AT-120-W is better for dense tower heatsinks or radiators because it delivers high static pressure. Choose the AT-120-W if you need maximum cooling power through tight fins.
What is the difference in static pressure between the two?
The AT-120-W has significantly higher static pressure than the AS-120-ARGB-WR. The AT-120-W is rated for 5.04 mmH2O, making it ideal for high-resistance setups like radiators. The AS-120-ARGB-WR provides 1.67 mmH2O, which is sufficient for standard airflow but not for pushing air through dense filters. Higher pressure means better performance against resistance.
Are both fans the same physical size?
Yes, both fans are 120mm in size. The AS-120-ARGB-WR measures 4.72 inches by 4.72 inches with a height of 0.98 inches. This standard size allows them to fit in most cases that accept 120mm fans. You can swap them in standard mounting locations without needing adapters or different case layouts.
Which fan is quieter during idle times?
The AS-120-ARGB-WR is noted for quiet operation during idle times. It is designed to prioritize silence over maximum pressure. The AT-120-W focuses on static pressure for radiators, which may generate more noise under load. If you want a silent build when the PC is not under heavy stress, the AS-120-ARGB-WR is the practical choice.
Is the AS-120-ARGB-WR a reverse fan?
Yes, the AS-120-ARGB-WR is a reverse fan. It uses a reverse blade design to direct airflow outward. This keeps the ARGB side facing the viewer, hiding the motor and frame struts. It is specifically recommended for rear exhaust positions or outward-facing lighting setups where aesthetics are a priority for your build.